Rinnai · Error code 10 · Checked November 2026
Rinnai error code 10: air or exhaust blockage
Air isn’t getting in or exhaust isn’t getting out, so the heater shut down. On condensing models, a full or frozen condensate trap does it too. Start with the vent outside and the drain line.
Smell gas? Don’t touch any switch or try to reset anything. Leave the house, then call 911 or your gas company from outside. In Southern California that’s SoCalGas, 1-800-427-2200.
From Dan and Dave at Dan's Plumbing, a family plumbing shop in Westlake Village, California. Everything below comes from Rinnai’s own documents, cited line by line.
What it means
What Rinnai says code 10 means
“Air Supply, Exhaust Blockage or Condensate Trap is Full”— Troubleshooting Tankless Water Heater Diagnostic Codes, page 12
Rinnai calls code 10 an “air supply or exhaust blockage.” The heater can’t move enough air in or exhaust out, so it shuts down. On condensing SENSEI, RX and CX models, the same code also means the condensate trap inside is full, usually from a clogged or frozen drain line.
Start outside: look at the vent and air intake for snow, leaves, nests or anything stacked against them. Then make sure the small condensate drain line is draining. Rinnai’s guide lists vent build problems, a dirty internal air filter, the fan and debris in the burner as what a technician checks next.
Model differences. SENSEI, RX and CX: 10 also means the internal condensate trap is full (usually a clogged or frozen drain line). KB/KBD/KBP: owner table adds 'Burner Sensor (see code 31)' under code 10 (KBD p. 60). RE/REP: check vent length matches the vent-length parameter (RE p. 49). RH180: 4 in. B-vent only (guide p. 14).
On other Rinnai models, 10 means something else:
- EC52 T3 failureThe evaporator coil temperature sensor failed. On: REHP heat pump water heater (tank).
Why it happens
Likely causes of Rinnai code 10
- Condensate drain line clogged or frozen, backing up into the internal trap (SENSEI/RX/CX). (Diagnostic codes guide (2024), p. 12)
- Blocked or wrongly built vent: wrong materials, joints not fully seated, too long, crushed by foam sealant, debris or insects, poor terminal clearances. (Diagnostic codes guide (2024), p. 12)
- Dirty internal air filter (SENSEI/RX/CX indoor units). (Diagnostic codes guide (2024), p. 12)
- Fan problems: debris in fan wheel, stuck check valve behind fan, bad fan motor, harness or PC board. (Diagnostic codes guide (2024), p. 13)
- Wrong high-altitude setting; on Non-SENSEI, wrong manifold pressures or vent-length DIP switches. (Diagnostic codes guide (2024), p. 15)
- Debris or scale between burner/heat-exchanger fins. (Diagnostic codes guide (2024), p. 15)
What to do
Safe checks first. Then call a pro.
Safe checks you can do
Make sure the condensate drain line is draining and not clogged or frozen (condensing units). (RU manual, p. 73)
Look outside: check that nothing is blocking the flue inlet or exhaust (snow, leaves, nests). (V series manual, p. 34)
Check all vent components for proper connections (visible joints). (V series manual, p. 34)
Keep the area around the flue terminal and the condensate drain free of snow and ice. (RU manual, p. 77)
What a technician checks, and why
- Clean the internal air filter under the front cover (SENSEI/RX/CX indoor).Requires removing the front cover and working inside the cabinet. (Diagnostic codes guide (2024), p. 12)
- Inspect the whole intake and exhaust system: approved materials, insertion depth, vent lubricant, equivalent length (90° elbow = 6 ft, 45° = 3 ft for Rinnai concentric), terminal clearances.Vent system changes and vent-length/DIP settings are installer work. (Diagnostic codes guide (2024), p. 12)
- Test only while it is coding: briefly remove the exhaust section and see if the heater runs; reconnect immediately.Rinnai warns never to leave a heater running with the vent disconnected. (Diagnostic codes guide (2024), p. 12)
- Remove the fan; inspect wheel, housing, air duct and the check valve behind the fan.Requires removing the front cover and working inside the cabinet. (Diagnostic codes guide (2024), p. 13)
- Verify high-altitude parameter (SENSEI) or altitude/vent DIP switches and manifold pressures (Non-SENSEI).Gas pressure, gas type and gas-line work need a qualified gas technician. (Diagnostic codes guide (2024), p. 15)
- Pull the heat exchanger/burner and clear debris from burner and fins; do not blow SENSEI burners out with compressed air.Opens the burner/combustion chamber or gas valve. (Diagnostic codes guide (2024), p. 13)
- Replace fan motor, fan harness or PC board if still failing.Requires removing the front cover and working inside the cabinet. (Diagnostic codes guide (2024), p. 13)
Please don’t
- Don’t open the burner, the gas valve or the sealed combustion chamber.
- Don’t keep resetting a code that keeps coming back. A code that returns means the cause is still there.
- Don’t bypass or unplug a safety sensor to get hot water back.
- Don’t cover, tape or move the vent or the air intake.
Heater getting old, or the same code keeps coming back? Repair or replace? Three taps and Dan’s answer → Or see what a water heater repair usually involves.
Common questions
Rinnai code 10 questions
Can a frozen condensate line cause Rinnai code 10?
Yes, on condensing models. Rinnai’s guide says a clogged or frozen condensate drain backs water up into the trap inside the heater, and the heater shows 10. Keep the drain and the vent outside clear of snow and ice.
Where this comes from
Sources
Taken from Rinnai’s own documents, checked November 13, 2026. Page numbers are the printed page. Where models differ, we say which model each part applies to.
- Troubleshooting Tankless Water Heater Diagnostic Codes Rinnai America Corporation · 100000652 · file '100000652-Troubleshooting TWH Diagnostic Codes (3).pdf', PDF dated 2024-05-08; byte-identical to the library’s 'TWH Troubleshooting Technical Data Sheet' · Models: RU/RUR/RSC/CU SENSEI, RX/RXP/CX/CXP SENSEI RX/CX, RE/REP (VE), V53e/V53De/V65/V75/V94/V94X (VC Value), RL75/RL94/RLX94 (VC Luxury, VB), R50LS/R63LS/R75LS/R94LS/R98LS (VA), RC80/RC98 (KA), RU80/RU90/RU98, RUC80/90/98, C199 (KB/KBD), RUR98 (KBP), RUCS65/75, RUS65/75 (KCM), RH180 (HTT)
- Tankless Water Heater (Residential) Installation and Operation Manual — RU199/RU180/RU160/RU130 i/e Rinnai America Corporation · 100000467 · (07) · Models: RU199i, RU180i, RU160i, RU130i, RU199e, RU180e, RU160e, RU130e
- Direct Vent Tankless Water Heater Installation and Operation Manual — Value Series (V94i, V94Xi, V75i, V65i, V94e, V75e, V65e) Rinnai America Corporation · 100000258 / U307-1120X04 · (10) · Models: V94i, V94Xi, V75i, V65i, V94e, V75e, V65e
Water heater help
More about water heaters
Code won’t clear?
If you’re within about 30 miles of Westlake Village, call or text Dan a photo of the display and the label. He’ll tell you what it is.
Or send the details and Dan will call you back. Monday to Friday, 9am – 5pm.

