Bradford White · Status light 7 blinks · Checked November 2026
Bradford White flammable vapor sensor lockout: 7 blinks
On a Bradford White power vent, power direct vent, damper or RG2F tank, 7 blinks then a pause means the flammable vapor sensor locked the heater out. On a standard atmospheric tank, 7 blinks means something else.
Smell gas? Don’t touch any switch or try to reset anything. Leave the house, then call 911 or your gas company from outside. In Southern California that’s SoCalGas, 1-800-427-2200.
From Dan and Dave at Dan's Plumbing, a family plumbing shop in Westlake Village, California. We install Bradford White heaters. Everything below comes from Bradford White’s own documents, cited line by line.
What it means
What Bradford White says code 7 blinks means
“Flammable vapor sensor or simulative resistance device out of specification.”— Service Manual: PV Series Power Vent Gas Water Heaters, page 16
Bradford White’s service manuals call 7 blinks a “flammable vapor sensor (FV sensor) fault / lockout.” The sensor’s reading is out of range, so the heater locks out and won’t light. Fumes from gasoline, paint or solvents stored near the heater can do it. So can a wet or overheated sensor, or a wiring problem.
It only means this on tanks with electronic ignition: power vent and power direct vent models, D Series damper tanks and the RG2F. On a standard atmospheric Defender tank with a pilot, 7 blinks is a gas control fault. On eF Series condensing tanks, which have no vapor sensor, 7 blinks means the resistor plug that stands in for it is out of range or unplugged.
Bradford White says the lockout lasts until the power is cycled. A related code, 8-1 blinks, means the vapor sensor reads too low, which can be a short in the sensor or its wiring.
Model differences. This is the Bradford White 'flammable vapor sensor lockout'. It exists only on electronic-ignition models that have an FV sensor: power vent / power direct vent RG-LG PV & PDV, Ultra Low NOx power vent, D Series damper, URG D, RG2F and pre-2015 TTW/PDX. RG1PV55H and RG2PV75H use a simulated resistive device instead of a sensor (bw-51540 p. 11). On eF Series condensing models 7 flashes means a simulated-resistive-device fault (next entry). On standing-pilot atmospheric tanks 7 flashes is a gas control fault. Lockout: indefinite, cycle power to restart (bw-51540 p. 10). The sequence-of-operation text adds a two-part version: above 65,000 ohms the control 'flashes 7 times, then once' (7-1) during a 2-minute verify delay, repeated up to 5 times before the lockout (bw-51540 p. 12; bw-51637 p. 9); the charts and quick guides list only 'Seven flashes'.
On other Bradford White models, 7 blinks means something else:
- Seven flashes and three second pauseThe gas control’s electronics found a fault. On: ICON 1.0 standing-pilot control (through serial code TA, Jan 2019); Eco-Defender Ultra Low NOx tank, ICON 1.0; Eco-Defender Ultra Low NOx tank, before 2015.
- Seven flash, three second pause - simulated resistive device (eF Series)eF Series condensing models have no vapor sensor; a resistor plug stands in for it. On: eF Series condensing power vent.
Why it happens
Likely causes of Bradford White code 7 blinks
- Flammable vapor present. (Owner’s manual 238-54331-00B, p. 33)
- Flammable vapor sensor exposed to excessive moisture. (Owner’s manual 238-54331-00B, p. 33)
- Flammable vapor sensor exposed to extreme ambient temperature. (Owner’s manual 238-54331-00B, p. 33)
- Resettable thermal switch open (Ultra Low NOx power vent, D Series, RG2F). (Service manual 238-51548-00D, p. 15)
- Sensor resistance above 70,000 ohms: control retries every 2 minutes up to 5 times, then goes into flammable vapor lockout. (Service manual 238-51540-00E, p. 12)
- Pre-2015 power vent: indicates gasoline vapors were detected at potentially explosive levels. (Service manual 238-46238A-00A, p. 14)
What to do
Safe checks first. Then call a pro.
Safe checks you can do
Check for gasoline, paint, thinner, solvents or other flammable products near the heater. Remove them and air out the area. If you smell gas, follow the gas-smell instructions instead. (Service manual 238-46238A-00A, p. 14)
Look for water or a wet floor around the base of the heater (a wet sensor causes this code). (Owner’s manual 238-54331-00B, p. 33)
Only after any vapors are gone: reset by cycling power (unplug/replug or the gas control ON/OFF switch). The lockout does not clear by itself. (Service manual 238-51540-00E, p. 10)
To clear the code:
- Flammable vapor sensor / simulated resistive load lockout lasts indefinitely; cycle power to restart. Soft lockouts retry after 5 minutes; hardware errors self-clear after the fault is gone 15 seconds. (Service manual 238-51540-00E, p. 10)
- Pre-2015 power vent: reset a 7-flash flammable vapor sensor fault by cycling power to the appliance or cycling the ON/OFF switch, only after verifying no gasoline vapors are present. (Service manual 238-46238A-00A, p. 14)
What a technician checks, and why
- Flammable vapor sensor test: power OFF, unplug the sensor, measure with pin probes; must be 3,000-48,000 ohms, otherwise replace the sensor.Needs a meter or manometer and work on the gas control; service manual is for qualified service providers. (Service manual 238-51540-00E, p. 33)
- RG2F: measure both the flammable vapor sensor and the resettable thermal switch (left two pins); both must be 3,000-48,000 ohms; if the switch has not tripped and is out of range, replace it.Needs a meter or manometer and work on the gas control; service manual is for qualified service providers. (Service manual 238-51617-00C, p. 22)
- Check sensor harness.Needs the outer/inner door or control opened; the service manual is for qualified service providers only. (Power vent quick service guide, p. 1)
- Resettable thermal switch testing.Needs the outer/inner door or control opened; the service manual is for qualified service providers only. (Service manual 238-51548-00D, p. 15)
- Replace the Flammable Vapor Sensor element if a gasoline spill event occurred.A vapor event needs a technician to inspect the heater. (Service manual 238-46238A-00A, p. 14)
- D Series / URG D: check continuity on the temp limit and clean the intake screen.Needs the outer/inner door or control opened; the service manual is for qualified service providers only. (Quick service guide 238-55599-00A, p. 1)
Please don’t
- Don’t open the burner, the gas valve or the sealed combustion chamber.
- Don’t keep resetting a code that keeps coming back. A code that returns means the cause is still there.
- Don’t bypass or unplug a safety sensor to get hot water back.
- Don’t cover, tape or move the vent or the air intake.
Heater getting old, or the same code keeps coming back? Repair or replace? Three taps and Dan’s answer → Or see what a water heater repair usually involves.
Common questions
Bradford White code 7 blinks questions
What does it mean when my Bradford White blinks 7 times?
It depends on the tank. On a power vent, power direct vent, damper or RG2F tank, 7 blinks is a flammable vapor sensor lockout. On a standard atmospheric tank with a pilot, 7 blinks means the gas control’s electronics found a fault. Look at whether your heater has a fan on top or a damper on the vent: those are the electronic-ignition models.
How do I reset a Bradford White flammable vapor sensor lockout?
Bradford White’s service manual says the lockout lasts until power to the heater is cycled. First get rid of the cause: air out any gasoline, paint or solvent fumes and move those products away from the heater. If it locks out again, the sensor or its wiring needs a technician.
Do I need a new water heater after a flammable vapor sensor lockout?
Not usually. Bradford White’s manuals point to the cause first: fumes, a wet or overheated sensor, or the wiring. A technician tests the sensor and its harness. Replacing the whole heater isn’t the first step.
Where this comes from
Sources
Taken from Bradford White’s own documents, checked November 13, 2026. Page numbers are the printed page. Where models differ, we say which model each part applies to.
- Service Manual: PV Series Power Vent Gas Water Heaters Bradford White Corporation · 238-51540-00E · 4/19 · Models: RG1PV40S, RG1PV50S, RG1PV55H, RG2PV40T, RG2PV50H, RG2PV50T, RG2PV75H, RG2PV60T, LG1PV55H78, LG2PV50H65, LG2PV75H76
- Installation and Operation Instruction Manual, Power Vent Gas Water Heater (owner’s manual) Bradford White Corporation · 238-54331-00B · REV 03/24 · Models: RG1/RG2 PV 40/50 gal
- Service Manual: UPV Series Ultra Low NOx Through-The-Wall Gas Water Heaters Bradford White Corporation · 238-51548-00D · 12/20 · Models: URG1PV40S, URG1PV50S, URG2PV40T, URG2PV50T, URG2PV50H, ULG2PV50H56
- Service Manual: TTW Series Through-The-Wall Gas Water Heaters (archived, pre-2015) Bradford White Corporation · 238-46238A-00A · not printed · Models: M1TW40S, M1TW50S, M1TW60T, M4TW40T, M4TW50T, M4TW60T, M2TW50T, M2TW65T, TW450S65F, TW465S65F
- Service Manual: High EF Atmospheric Vent Gas Water Heater Bradford White Corporation · 238-51617-00C · (10/20) · Models: RG2F40S, RG2F50S
- Quick service guide: Power Vent, Power Direct Vent, & Fan Assisted Water Heaters - ICON Bradford White Corporation · not printed · not printed · Models: RG/LG PV, RG/LG PDV, RG2F
- Quick Service Guide / Service Manual Supplement: (U)RG Atmospheric Damper Models With ICON System, Serial date code KA (January 2013 and later) Bradford White Corporation · 238-55599-00A · not printed · Models: RG1D, URG1D, URG2D
Water heater help
More about water heaters
Code won’t clear?
If you’re within about 30 miles of Westlake Village, call or text Dan a photo of the display and the label. He’ll tell you what it is.
Or send the details and Dan will call you back. Monday to Friday, 9am – 5pm.

